• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Cat flaps allow your pet move around at their own pace without needing to let him in or out. They also help stop your cat from urinating inside the house.

It is simpler to install the cat flap on a upvc panel than on a glass one, but you will need some skills and the appropriate tools.

Measure the Door

Installing a cat door into the front door is difficult however, provided that the cat flap is the correct one and you follow the directions it shouldn't be too difficult. We will show you how much to install a cat flap to draw the shape, use a jigsaw to cut out the door's area and then finish the job by attaching the flap to the door. This will ensure that the flap stays in position and shields the doors from damage caused by wind and rain.

The first step is take a measurement of the width of your pet to get a precise measurement of the size of cat flap you'll need. This will ensure that the flap is big enough that your pet can go inside and out of the house without having to open or close the door each time, but also small enough to keep them from going too far in either direction.

If your kit comes with an illustration of the location to drill, you can put it on the door, and then draw a pencil around it. If your door has sill or moulding along the bottom edge then make sure you have enough clearance from these because this will keep your cat safe and prevent them gaining access to your home.

Next put on your eye protection and dust mask and using a jigsaw begin to cut along the line that you penciled in, don't try to push the blade too hard because this could make it cut faster than you'd like it to. Use a set square to ensure that you are cutting the material properly and that the hole is a rectangle. When you are happy with the result, you are able to remove the remaining door material.

Draw a Line

The cat flap lets you to let your pet go inside and out without having to worry about unwanted visitors or unwelcome gifts. It also reduces drafts and helps keep the temperature of your home in a stable manner. However, putting a cat flap in your door could be an overwhelming task for those who have never done it before, leading many to hire a professional joiner or carpenter to do the job. While this is certainly an option, it's possible to do the job yourself if you have the proper tools and follow instructions with care.

While this is far easier to do with a wooden door, it is still possible in uPVC doors, but you should be cautious not to damage the doors, as this can invalidate your warranty. The first step in the process is to measure the door and ensure that it is able to accommodate the new cat flap. If you have a standard uPVC panel, this should be easy. However in the case of made of composite or another kind of door, you might have to be more cautious.

The next step is to measure the size of your cat's belly. This is the amount of height between the floor and the bottom of your cat's stomach. You will need to locate an area on the door that allows your cat flap in upvc door cost to move through easily. Once you know this you'll need to mark out the area using pencil and a spirit level to be sure that the hole you make will be a good fit for your cat.

After you have marked the area, you're now ready to cut the hole. It is essential to be patient and use a jigsaw in order to ensure the cuts are smooth and clean not uneven and rough. This could damage your door. Wear safety glasses and a dust mask while using a jigsaw. Inhaling sawdust is dangerous for your health. After you have finished cutting the hole, you'll require sandpaper to smooth the edges so that the cat flap is easily fitted into place.

Cut a hole

It isn't easy to fit an animal flap on a door panel or sealed double glazing unit. You may be tempted to tackle the task yourself, but unless have a lot of experience with DIY, it's likely to be best to have a professional in to do the job for you. A faulty job can not only be unsightly, but also pose an security risk. It could allow cold air to enter when the cat is outdoors and hot air to escape when it is inside.

Mark the hole's position on the door using an eraser and a spirit level. This will ensure it is positioned correctly and is flush with the door's other parts. It is important to have a piece of sandpaper at ready for any rough edges.

After the line is traced, you must cut the hole using the jigsaw. Remember to wear any necessary safety equipment for working with an electric tool. If you're concerned about the noise, you can get an electric jigsaw that is quieter and easier.

You should only remove the material needed to fit the flap. A little bit of extra material will be required for the thickness of the the flap but removing more than that can cause problems and even harm the frame of the door.

A door made of upvc may include a metal frame, or panel within it which could block the microchip cat flaps for french doors flap and in this case you will need to cut an oversize hole so that the metal doesn't come into contact with the wall of the cat flap. If this is done, it is crucial to fill in the oversize gap and render it watertight.

If you are fitting cat flap in upvc door panel - visit the next page - a cat flap into the frame of a double glazed windows with a metal frame, you'll need to speak to a specialist who can supply you with a new glass pane that already has the hole for the cat flap premade inside. It is much less expensive to have this done instead of trying to install the cat flap onto an existing pane of glass that was not designed specifically for this purpose.

Place the Flap

Cat flaps give your pet the freedom to move around whenever they want and allow them to be comfortable in the house when they'd like. If you've got a uPVC door, it may be difficult to put in an animal flap, especially if you don't own glass panes that can be cut for one. If you're able to buy and install a new half-glazed uPVC panel, it's possible to install a cat flap to these doors. It's not a simple matter of slicing a hole into the door. You'll also need to perform a few steps to ensure that the door is secure.

A composite, uPVC, or GRP door panel typically comprises an extremely thin plastic outer skin joined to a soft polystyrene insulating core. It is essential to be careful when cutting the material. This type door comes with a template that you can use to make the hole.

Once you've marked the opening in your front door, it is time to put in the cat flap step flap. You can purchase and install many different models that range from simple button operated ones to ones that are activated by microchips that allow only your pet. Whatever kind of cat flaps you choose it's essential that your cat can use the flap without getting stuck outside in the rain.

It's a good idea select circular fittings instead of one that is square, because circles are more securely cut into the door glass. This is because square holes are more likely to break the glass when drilled. This is also a safer choice since you don't have to drill into the toughened glass, which could break and cause harm to your pet or your family members. This is particularly important if there are elderly or children in your home that could be hurt by glass fragments.