• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Fix a Loose Door Hinge

Most homeowners can fix door hinge (written by Technetbloggers) hinges that are loose. If the holes for screws have been stripped and will not hold screws, you might require wood glue and dowels to put back in the hinge.

Brush away any surface corrosion. This will help keep the dowels in place and provide a solid foundation for them to rest on.

Removing the Hinges

Most hinges on doors are able to be removed, making it easier to move the door from one side to the other or to take the entire door off the frame should it be needed. It is easy for anyone with a bit of patience, though you do need to know how do it right.

If the hinges have been painted you'll need to take off it prior to trying to remove the pins. If you don't, the paint could flake off and scratch the door when you attempt to lift it. To break the paint seal put the hinges in a stainless steel dish and fill the pan with water until the hinges are fully submerged. Let the hinges sit in the pan for 30 minutes. The heat from the water will soften the paint, making it easier to remove.

Once the pins are loosened, remove the hinges and the frame from the door. You can employ a screwdriver for the job done, but it is recommended that you make use of a magnetic screwdriver for this task. This type of screwdriver was created to grab screws made of steel and will make the project run much more quickly.

It is a good practice to spray lubricant on the hinges prior to trying to remove them. A simple lubricant will help the process to go more quickly and help you remove the pins and screws. You can find this type of lubricant at a variety of hardware and home improvement stores.

The number of hinges you need will also depend on what type of door you have and how it's installed. Heavier doors and solid-core doors will need more hinges, while hollow-core doors with a lighter weight may only require two or three hinges.

Understanding the various types of hinges will help you decide which one is the best for your particular situation. Exterior hinges are designed to withstand the weight of a door, while interior hinges must be able to support heavier loads.

Reattaching the Hinges

Over time the hinges on doors can loosen and begin to hang crooked or sag. This can be a major issue, but the solution is usually quite simple. A simple retightening will usually solve the problem. If the screw holes have been ripped out, it can be difficult to do. A wood dowel could be used to tighten these holes again.

Begin by drilling out the hole from the previous one using a drill bit that is similar to the size of the new screw (typically 3/8"). Fill in the hole using wood glue and a wooden stick. To ensure a tight fit, the dowel should be cut at the same length as the screw. After that, reinstall the screw and tighten it to the desired degree of tightness. If the door continues to have the tendency to be bowed the door, then add a second dowel to the gap and repeat the procedure. Close the door slowly after each adjustment to make sure that the perimeter clearances are in order.

Another option is to just use the wood plug instead of a dowel. It will work similarly, but it may take a bit longer to set up. You can tap in the wood piece that has been whittled to the proper size. If you don't have a wooden tool, you can also try using toothpicks or wooden matches.

After you've reinstalled your new screw and countersink the screw, you can use a countersink tool to make the hole for the screw's head smaller, so that it doesn't rub against the edge of the door when it is opened and closed. This will make it much easier to tighten the screws when reinstalling hinges.

After you have reinstalled the hinge, be sure to lubricate it with a dry lubricant in order to help keep it from getting stuck in the future. You can use products like PB Blaster and Liquid Wrench. Apply a thin coat and allow it to take approximately 15 minutes to reach the barrel of the hinge.

Refinishing the Hinges

If you're not sure if you're ready to replace the hinges on your door, you can make a few repairs. Make sure the screws that hold the hinge plate in place to the door frame as well as the frame are tight. If they're loose, tighten them using an electric drill or screwdriver. Be careful not too tighten the screws as this can cause gaps to appear at the trim joints or worse, strip the threads.

If the problem is that the hinge plates are separated from the door and jamb it is possible to reattach them by applying wood glue to the plate's back and then inserting wooden dowels or toothpicks into the holes. The toothpicks or dowels will provide a solid base for the screws and to prevent the plates from shifting when you drive them into place. Let the glue dry before reattaching the hinge.

Another common cause of loose hinges is that screws are worn out or are missing. It is possible to fix this issue by replacing the screws with larger ones. Make sure you use a drill bit that is compatible with the size of the screw hole in order to avoid drilling into other parts of the jamb or hinge.

After you've reattached your hinge, close the door and look at the gap between the door and the frame. The gap should be about the thickness of a penny all around or less if the old door was not hung correctly. If the hinges were set up properly, this shouldn't be an issue.

If you find that the hinges are loose, try adding the thicker shim of the hinge between the upvc window hinge replacement cost plate and the mounting surface, to create an extra inch of space. You can also take off the hinge pin and pound it down with a hammer in order to tighten it up or choose an entirely new hinge. You can also lubricate the hinges with mineral or jojoba oil to decrease friction hinges and aid in holding their place. Periodically lubricating your hinges can help keep them from becoming stiff or squeaky and will also prolong their lifespan.

Cleaning the Hinges

The friction created by a hinge's constant movement attracts dust particles. These particles may get stuck and accumulate over time in the moving parts of door hinges if they are not cleaned and lubricated regularly. In the end the hinge can become stiff and creaky and its appearance could get worse. Regular cleaning, lubrication, and inspections will maintain the functionality and quality of hinges on doors.

Examine the hinges to determine how much rust has built up on their surfaces. If the rust has become so severe that it has damaged the surface of the screw holes or the barrel of the hinge, you'll need to replace the hinges. If you're able to save the hinges, you can remove any loose rust with a wire brush and steel wool. Apply a commercial rust removal solution or a homemade solution such as lemon juice on the hinge. Let the rust remover be on the hinge for a few minutes to penetrate and dissolve any remaining rust.

Retightening screws can help restore hinge function if you don't want to spend time or money on replacing upvc window hinges hinges. It may be necessary to attach an shim of wood or a dowel to the upvc window hinge in the event that the screws have been stripped. Wooden dowels are round pieces of wood in the form of rods that are available in various lengths and sizes. They can be purchased online, at stores selling woodworking supplies and home improvement centers.

A shim could be made of plastic or metal, based on the kind of hinge you've got. To make a dowel cut a piece of wood dowel or any other durable material to the desired size. Then, dip a dowel into the adhesive of a carpenter and then insert it into the hole. The glue will hold the dowel firmly in place.

Before cleaning the hinges, lay down a piece of paper cloth or towel to protect your flooring from spills. After the area has been secured, proceed to clean the hinges with a soft cloth or sponge dipped in a mild cleaner or vinegar to get rid of dirt, grime, and tarnish. You can make use of a small or toothbrush brush to reach hard-to-reach spots in tight spaces and crevices.